what paint will turn my gold fixtures to silver
Practice you have the old schoolhouse Hollywood Lights in your Bathroom? Update them with this tutorial on how to spray pigment a light fixture.
Sick of looking at that 90s brass Hollywood-style light fixture in your bathroom?
Yep. That was me, too!
With a little spray pigment and some new light bulbs, this light fixture is brought into the present, at least equally much equally information technology could.
And so, if you lot're saving upward for when you tin redo the whole bath or you only want a trivial alter, this post will give you a simple and easy way to spray paint the lite fixture in your bath.
Let'southward do it!
Table of contents
- Assemble your materials
- Remove calorie-free bulbs and round covers
- Remove the silverish part
- Remove the gold cover of the low-cal fixture with a paint can opener
- Wipe the parts clean
- Set up plastic outside with your items and spray pigment the pieces of the light fixture
- Employ a few coats until satisfied
- Allow dry and put the spray painted low-cal fixture back together
- Video Tutorial
- Oft Asked Questions
Disclaimer: This post does include affiliate links for your convenience. This is at NO additional cost to you lot merely earns me a small commission. To read more than, bank check out our disclosure policy.
Gather your materials
Y'all volition not demand a lot of items for this projection, only everything I used is shown in a shoppable motion picture beneath except the paint tin can opener. That's the only other thing you'll need.
(click on any of the images to shop the products)
Remove calorie-free bulbs and round covers
First, you'll want to remove your light bulbs. After that, remove the covers surrounding the light fixture sockets.
We thought that they screwed on, but actually they were just on there with tension.
Twisting them back and along as you pull them forward was the easiest way to get them off.
Remove the silver part
Turns out the silver part that was over the brass was but a pocket-size piece of plastic held on by scotch tape haha.
Nosotros still removed it so that we could just spray the bodily slice.
Remove the gilt cover of the calorie-free fixture with a paint tin can opener
We weren't too sure how this was fastened, only since there were no screws to be found, we assumed it was clipped on somehow.
We tried to but pull it, but zilch happened, so we got creative…
Grab any paint can opener you lot have and use it to pry the gold cover from the light fixture.
When you are done, this is what will exist left on the wall.
The best office about this project is nosotros didn't have to mess with any electrical or removing the whole fixture from the wall.
Wipe the parts clean
Subsequently removing the parts, we wiped everything down.
The scotch tape on the panel slice required a footling goo-b-gone, merely the circular pieces above only needed to be wiped downwards with a damp rag.
Ready plastic exterior with your items and spray pigment the pieces of the low-cal fixture
Lay everything out and then you have a good view of every bending.
If you lot can figure out a mode to elevate the items off the ground, that may be easier to cover all the angles.
I set this upward in the driveway with a plastic tarp held down by heavy objects on either side so the tarp didn't blow effectually.
When I was spray painting, I didn't worry too much near the inside of the round pieces because I wanted a little touch of gold, simply information technology doesn't take much to cover each side.
It just may crave more coats.
Employ a few coats until satisfied
Follow the directions on the tin can. The picture above is after one coat, but I practical another coat afterward 20 minutes.
The automotive primer has a matte finish, then if you lot want a glossier finish, you volition need to purchase a top coat to spray over this.
I actually liked the matte terminate, so I did not apply a elevation glaze.
Video Tutorial
Frequently Asked Questions
Do YOU Have TO TAKE THE Low-cal FIXTURE DOWN TO SPRAY Information technology?
I would highly recommend it only considering information technology does not take much to remove the pieces. Also since you lot don't have to remove the actual wiring office of the fixture, you'll save yourself time and free energy taking information technology down. Otherwise, yous'll accept to protect a lot of expanse against overspray.
DOES THE SPRAY Paint WITHSTAND THE HEAT OF THE Lite BULBS?
I actually purchased LED bulbs that do non give off any rut for this very reason. Since I used automotive primer equally my spray paint, I don't think it would exist an result regardless, but to be prophylactic, use LED bulbs.
Other Posts Yous May Similar:
Reader Interactions
Source: https://myhomierhome.com/how-to-spray-paint-a-light-fixture/
0 Response to "what paint will turn my gold fixtures to silver"
Post a Comment